Відео

I have a Baofeng UV-5RM will the File Baofeng_UV_RR.img work with my model?

Yall still have the compressor? How’s it holding up?

mucho Gracias señor 5150

Check oil first make sure crank case ain't full of gas oil mix???

Mine didn’t come with directions so I’m trying to figure out the correct order of washer/locking washer used to connect the rack to the brackets..? Your video didn’t actually explain anything. 🤷‍♂️”bolt it together and put it on top” like obviously. Would love to have seen the directions you flashed the camera one time to.

Whats the Mishimoto part number for the radiator you installed. Where did you buy the radiator?

1:42 the either bunny took it

What is available for just the "middle" of gladiator? I don't need a full set but would see benefit to the breakover area for High Centering.

That was awesome to watch. Good job guys. 👏🏽

I'm thinking about just installing Nemesis front fenders only, i dont see a significant difference betweeen the back and factory units, and would save me changing out my factory bumper, which I like.

Clamp the bar on and use the correct size drill bit for the nutsert would’ve probably been a lot less work.

Does the windshield fully seal with and fold back up properly without any modification even with the rockhard cage kit?

I like your videos! They show how it REALLY is doing this work! I'm 62, I just did this! I don't want to do it again! Getting too old to be crawling around under these jeeps! 3 days to recover from a half day of work!!! I did both front and rear brackets...

This helped me out because I was missing my handle but I took a tube and smacked the end of it and it works

On your CHIRP file what are all the SEA channels associated with?

What's the tow capacity of that bumper?

Great job.help me a lot with my project.thankmypu

Its been 3 year but what numeration is on the front springs?

Can you mix 2 or 3 bottles to be ready or not recommend?

How does it look after 4 year? Sun fade? Peeling? Would you do it again?

how is this bumper holding up?

Why are you wearing such a nice shirt while you're mixing paint? Did your wife kick your ass later?

Wow. An old Roll A Long Custom F-350 just like mine! Also, too bad Banks stopped making these headers. I was going to do the same thing to mine.

Rugged GMR25 is not listed on chirp menu, what would be compatible to program? Or is there another software program to program? Thank you!

Can you add privacy channels. Our off road park uses 17-25 on a rugged radio system. Thank you.

what axle seals are you using that are "way more reliable" than the MOPAR units?

Well, how is the cage treating yall after a year of running it?

SUPER GREAT VIDEO... How good a painter does a guy need to do this, can a NEW BEE with a lot of rattle can experience do this? I have a good compressor....

Nice Jeep man! What color did you use?

My 05 is losing coolant. I found water in the turbo any advice on what's causing this. It also runs hot when I have a load on it

I would like to get me one of these.

Hello. After removing the stock bumper, what is the estimated installation time, including electrical assembly???, thank you.

Just watched your video after deciding to go with tnt front fenders since I already have their sliders. I plan on going with the 4.5" fender for a little additional coverage. Just curious how they are holding up and if you would go with them again. Thanks.

gonna stick with steel skids.

excellent idea, thanks.

My 2000 Cherokee uses size 20 torx

My inner bags were broken and I lost a few but I bought them with more than was needed.

Did you need a resistor for the led indicator?

@5150 MotorSports Good repairing video,may I know if it's ok for you to review our foam cannon S V3.0?Thanks in advance!☺

Wow! Nice XJ! Please look at the Holly retro headlights. Can’t stand the look of the cheap lights😂

Is this the first time you do this? If so good job 👏 I’m going to do my Dodge Ram 2500 and watching as many videos as I can. Any regrets or recommendations? Thanks 🙏

Don’t waste your money on this bumper. It’s so weak that I can’t carry a 33” spare. So I don’t carry a spare and it’s so weak that I can’t even use the 2” receiver. I called EAG and asked them if they had any kind of extra support brackets to help hold the bumper up and they said no. I told them that they need to engineer something better because it’s dead weight that serves no purpose. One of the biggest wastes of money you can throw away

Looks like a bunch of newbies had a great day! We all had to start someplace. The main thing is to get started and amaze yourself what you and your jeep can do.

Two part question But I just purchased a new UV-5R and followed the steps everything worked perfectly. But now I’m the radio isn’t talking like saying “frequency” when I power it on nor is it giving me my “custom” welcome when I power it on. Is there something in the settings I need to change to fix these? Is it true that I won’t be able to transmit on any of the channels now with the new radio updates?

Would it be the same for a Grand Cherokee? Same engine.

Bulb orientation and"clocking" very helpful. Thanks

Got a 1995, in the same position crank/no start. It sat for a year or so before i got it. So far i have replaced the distributor and rotor, fuel filter, fuel pump, fuel pump fuse, new battery (old one was doa), and all 6 spark plugs. Even though all of that didnt work to start it still needed it. A pretty hard newbie over here, anyone got any ideas?

Good lookin rig bro!! Long-live the 2-door!!!

solid video... but can we talk about darth vader behind the camera 😅

very smart. earned my subscription :)